Logo

P0120 Engine Trouble Code

P0120 Engine

When you check engine light came on code P0120 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P0120 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

P0120 code can be about changing a broken oxygen sensor can lead to a busted catalytic convertor which can cost upwards of $1,300. Taking your vehicle into a service shop will cost you around $300 depending on the vehicle. But, an oxygen sensor is easy to replace on many vehicles and is detailed in the owner's manual PDF or in our website. If you know where this sensor is located, you only have to unclip the old oxygen sensor and replace it with a new sensor. Regardless of how you approach it, you should get this fixed right away.

P0120 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
0
Intake Valve Control Solenoid Circuit Low
1
Engine Oil Temperature Sensor Malfunction
2
Crankshaft Position Sensor A Circuit Malfunction
0
Exhaust Gas Recirculation Sensor B Circuit High

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P0120 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P0120 OBD-II Trouble Code The throttle position sensor ( P0120 code. Engine Oil Temperature Sensor Malfunction and Crankshaft Position Sensor A Circuit Malfunction causes most of code P0120.

Reason For P0120 Code

The reason of P0120 OBD-II Engine Trouble Code is Engine Oil Temperature Sensor Malfunction.

P0120 DTCs may also be triggered by engine faults earlier down the line. For example, a dirty MAF sensor might be causing the car to overcompensate in its fuel-trim adjustments. As a result, oxygen sensors are likely to report fuel mixture problems.

How To Repair P0120 Code

Before starting let's see P0120 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P0120 code stored in the ECU.
  • Technicians will note P0120 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

The pressure control solenoid B for the vehicle's clutch is giving the wrong voltage readings, there could be an issue with the solenoid, the sensor, the wiring, or with the clutch itself. Shifting may become harsh, and other transmission problems may occur.

The computer installed in each fuel-injected vehicle has to be aware of two factors before it can solve the proper cold-start air/fuel compound: the engine coolant temperature and the exterior air temperature. Your symptoms are exactly the same to a faulty engine coolant temperature sensor (ECT). The computer is measuring an air/fuel compound that is excessively meager.

Sometimes P0120 code comes with P012000 code.

Diagnosis Of Engine Error OBD Code P0120

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P0120 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P0120 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.